It looks ridiculous, but there’s actually a very good and logical reason I had some much smaller tires than the fronts mounted on the rear axle of my Jeep this morning. It’s up to you to guess what that reason is. If no one gets it, I’ll post the answer tomorrow morning.
Update: there were lots of good answers, several on the money and some close. Here’s my explanation at the bottom below:
FWIW, these are a pair of cheap used 205-60R15 tires which are 24.7″ inches tall. The front tires are 30″ tall. Does that help?
Answer: A number of you nailed it, starting with the first comment by Bobe. My CJ-5 came with 4.27 axles, a change (from 5.38s) Jeep made in about 1958 to accommodate the fact that more folks were driving their Jeeps on the highway. To compensate somewhat, they also made first and second gear on the three speed T90 transmission a bit lower, but it was a compromise, given the Hurricane F134’s 75 hp. And that was with the standard 600-16 tires, which are 28.3″ tall. So with the 30′ tires on my Jeep, it really felt geared too low. The gap between the gears was too large, it bogged when being upshifted, and third overdrive was utterly useless.
So I’ve been leaning towards putting in 5.38 axle gears. But it’s a big commitment as I’m not in a position to install the gears myself. And I’ve decided to also have Dana/Spicer Powr-Lok limited slip differentials installed at the same time. But how would it feel? Would I regret it?
On my pre-breakfast walk, I came up with the answer: put some smaller tires on the back that will essentially equal the final gearing of a 5.38 axle with a 30″ tire. That required a 24″ tire, so I went to my friendly nearby used tire store and had them install a pair of marginal 205-60R15s.
And yesterday I finally got one of the three all-electronic distributors (OMID-AXA) actually working right, meaning with its mechanical advance functional. Due to very poor workmanship, the mechanical advance in the one that was in it and one of the two spares that came with it were locked in place. I compensated by cranking up the advance on the one that was in it, but when I mixed components (the one with working advance had a dead electronics module) I got one proper distributor and set the timing. It now advances to around 30 degrees at 2500 rpm; a bit higher than factory specs, but then those were set in the early ’50s when gas had 80 octanes, if that.
The combination of the smaller tires with the perkier engine was…surprising. It really steps out now, given its 75 hp. The shift into second actually gives a bit of a nudge instead of an anti-nudge. Second overdrive keeps the party going and third is now a great all-round gear from 30 or so up to 50. And now third overdrive is very usable; just right for the highway or tootling down a fairly straight country road. It was 27 degrees and I still have the top down, so I didn’t take it on the freeway, but I’m sure it will run readily at 60 or more if it’s fairly level.
Everything now happens quicker and brisker, which makes driving and shifting the two sticks more fun. A huge improvement. So yes, I will be having those 5.38 gears installed. And quite likely a set of Terra-Low gears in my transfer case to bring Low range from 2.46 to 3.15. I’m signed up for a big 4×4 Jamboree in Southern Utah in late January, so now I just need to get my installer to find the time. It’s way above my current pay grade.


























Axle ratio accommodation
You got it, if you meant testing out a lower axle ratio.
To lower the overall gearing ?
As a test for that. Full answer in my updated post above.
Sits strangely level like that….
True. The 2.5″ lift is a bit butt-high. I did take out one leaf (the smallest one) in front, and I intend to take out one or possibly two in the rear.
My guess: The transfer case is locked engaged and the rear differential gear ratio is numerically higher than the front differential. The goal is to have the drive shafts rotate the same when moving and hope to not break anything while driving on pavement until the transfer case can be disengaged.
And while it looks odd, it sites level which is curious.
Guess 1: you found out the front and rear differential gearing is different and to avoid damage you have uneven tire sizes until you can correct the issue.
Guess 2: you are keeping it in 2wd and testing to see if you go to stock leaf springs and tire size do you still need to re-gear the differentials.
Guess 3: is it worth it to put on small cheap tires for when towing behind the Pro Master.
With the tall tires, the thing’s a dog around town (perhaps highway too) with the standard axle ratio.
If you leave it in 2-HI, you’ll have acceptable performance on-road, and when you go off-road you put on the big set stored…?
Thinking it’s you, there’s a simple means to adjust rear axle height.
Can’t play with maths right now, but it would be genius if Rubik-ing all the numbers together arrived at result that allows you 4wd anyway, or close enough for off road in a pinch.
That would be elegant.
You’re close; see full answer in my updated post. It’s trying out what 5.38 gears would feel like, but of course only on the street.
Did a previous owner jack up the back end and these bring it back to level?
The 2.5″ lift kit is a bit butt-high. I’m going to take one or two leaves out. But that’s not the reason; see my updated post above.
Well my first guess was how it drove with something close to the stock tire size since I know you mentioned de-lifting it. However what I’m seeing is that a 6.00-16 was the common size and the Military NDT repo tires are advertised as being 28.3″ tall. With the 15″ rim a 225/75-15 would be the equivalent diameter to the stock.
So second guess is in consideration of re-gearing the axles and see what it would drive like with a higher gear and stock diameter tires. Based on the numbers those tires and the standard 4cyl 4.27-1 ratio would have a very close rev per mile as the 4.88 ratio optional on the V-6 models with a set of tires that are around 28.3″ tall.
So did you find a set of 4.88 axles?
Full answer in my updated post. In essence, trying out what 5.38 gears would feel like compared to the 4.27s I have now.
I think you’ve changed your front axle to a 5.38 ratio and you haven’t found a rear axle yet so this allows you to keep driving on the 4.88 rear.
5.38/4.88=1.102 and 30/24.7=1.215 is 10% off but close enough for off road evaluation before you spring for the 2nd axle?
Oh wait, maybe it’s 4.27 to 5.38, that’s only 3% off with that tire combo.
Close. This is only a test, to see what 5.38s would feel like with my 30″ tires. See full answer above.
I’m flummoxed and subscribed so I can learn a new thing .
-Nate
Without taking the time to crunch the numbers as others have done, I’m guessing it’s to have more acceptable gear ratios (transmission and rear diff) when you’re using 2wd on paved roads. (In other words, what VDubDave said above.)